izpis_h1_title_alt

Control system for a tensile-testing device using low-cost hardware and open-source software
Kranjec, Matej (Avtor), Korinšek, Jernej (Avtor), Ambrož, Miha (Avtor), Kunc, Robert (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (1,28 MB)
URLURL - Izvorni URL, za dostop obiščite https://www.sv-jme.eu/article/control-system-for-tensile-testing-device-using-low-cost-hardware-and-open-source-software/ Povezava se odpre v novem oknu

Izvleček
The aim of this study is to verify whether a Raspberry Pi 3 B+ can be utilized as a low-cost device for controlling a tensile-testing device used for material research purposes. A list of requirements based on already-available hardware was drawn up, which the new control system had to fulfil. To connect all the necessary equipment, a connection board was constructed, and some additional hardware was acquired for the system to be able to perform all the necessary tasks. The whole controlling system was also put in a small enclosure to make it portable. The control-system software was written in C++ using the Pigpio library. The developed system was then tested, and the results were compared to a commercially available Instron 8802 device. A comparison of the results shows that the upgraded equipment can produce comparable results to commercially available devices and is sufficiently accurate to be applied for research purposes for the characterization of soft tissues and other materials.

Jezik:Angleški jezik
Ključne besede:Raspberry Pi, low-cost, tensile testing, measuring equipment
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Leto izida:2020
Št. strani:str. 155-163
Številčenje:Vol. 66, iss. 3
UDK:004.3:620.172(045)
ISSN pri članku:0039-2480
DOI:10.5545/sv-jme.2019.6418 Povezava se odpre v novem oknu
COBISS.SI-ID:17170203 Povezava se odpre v novem oknu
Število ogledov:13
Število prenosov:19
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
 
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
:
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Gradivo je del revije

Naslov:Strojniški vestnik
Skrajšan naslov:Stroj. vestn.
Založnik:Zveza strojnih inženirjev in tehnikov Slovenije [et al.], = Association of Mechanical Engineers and Technicians of Slovenia [et al.]
ISSN:0039-2480
COBISS.SI-ID:762116 Povezava se odpre v novem oknu

Gradivo je financirano iz projekta

Financer:ARRS - Agencija za raziskovalno dejavnost Republike Slovenije (ARRS)
Številka projekta:P2-0109
Naslov:Modeliranje v tehniki in medicini

Sekundarni jezik

Jezik:Slovenski jezik
Naslov:Krmilni sistem naprave za natezne preizkuse z uporabo cenovno ugodne strojne opreme in odprtokodnega programja
Ključne besede:krmilni sistemi, merilna oprema, natezne naprave, odprtokodno, nizkocenovna strojna oprema

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj