izpis_h1_title_alt

Sliding evolution of the mechanical behaviour of zinc dialkyldithiophosphate tribofilms on diamond-like carbon coatings
Bartolomé, Luis (Avtor), Oblak, Eva (Avtor), Kalin, Mitjan (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (1,15 MB)
URLURL - Izvorni URL, za dostop obiščite http://link.springer.com/article/10.1007%2Fs11249-016-0666-y Novo okno

Izvleček
The evolution of the mechanical behaviour of zinc dialkyldithiophosphate (ZDDP) tribofilms on diamond-like carbon coatings during sliding contact has been studied by combining nano-indentation experimental data and finite element modelling. The nano-indentation data from the ZDDP tribofilms were obtained for two different sliding distances of the tribological tests after 15,000 and 216,000 cycles, which correspond to 25 min and 6 h, respectively. A non-homogeneous structure was found for the ZDDP tribofilms after both sliding distances, which were also verified by the local stiffness using the AFM force modulation mode. A dual structure is observed for the ZDDP tribofilms after 15,000 cycles, while three distinct components with different mechanical behaviours were found after 216,000 cycles. It was also found that the mechanical behaviour of the harder component of the ZDDP tribofilms remains almost unchanged for both sliding times, while the softer component tends to stiffen slightly over the sliding time. In addition, using the proposed algorithm with finite element simulations, the mechanical properties of the different components have been obtained, e.g. the elastic modulus E = 25.5 GPa and the yield stress Y = 1.585 GPa of the harder component for both sliding times. The softer component exhibits E = 1.65 GPa and Y = 0.144 GPa after 15,000 cycles and E = 3.5 GPa and Y = 0.17 GPa after 216,000 cycles. Finally, an intermediate component with E = 11.7 GPa and Y = 0.94 GPa has been only found at 216,000 cycles.

Jezik:Angleški jezik
Ključne besede:DLC coatings, ZDDP, finite element method, AFM, tribofilms
Vrsta gradiva:Članek v reviji (dk_c)
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Leto izida:2016
Št. strani:str. 1-9
Številčenje:Vol. 62, iss. 2
UDK:539.92(045)
ISSN pri članku:1023-8883
DOI:10.1007/s11249-016-0666-y Povezava se odpre v novem oknu
COBISS.SI-ID:14585883 Povezava se odpre v novem oknu
Število ogledov:27
Število prenosov:4
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
 
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
:
Objavi na: Bookmark and Share

Gradivo je del revije

Naslov:Tribology letters
Skrajšan naslov:Tribol. lett.
Založnik:Baltzer, Baltzer Science Publishers
ISSN:1023-8883
COBISS.SI-ID:2806555 Novo okno

Gradivo je financirano iz projekta

Financer:ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
Program financ.:Raziskovalni projekti - aplikativni
Številka projekta:P2-0231
Naslov:Tribologija
Akronim:
ID projekta:info:eu-repo/grantAgreement/ARRS/Raziskovalni%20projekti%20-%20aplikativni/P2-0231

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:DLC prevleke, metoda končnih elementov, tribofilmi, tribologija

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj