izpis_h1_title_alt

Oblikovanje in konstruiranje tikove palube : diplomsko delo (visokošolski strokovni študij)
ID Bijol, Miha (Avtor), ID Hrovatin, Jasna (Mentor) Več o mentorju... Povezava se odpre v novem oknu, ID Šernek, Milan (Recenzent)

.pdfPDF - Predstavitvena datoteka, prenos (2,50 MB)
MD5: 201CC25345A718082242B033906C51CB
PID: 20.500.12556/rul/148506df-1fad-4524-b5d9-f2aee0cd8e0c

Izvleček
Podjetje Elan Marine je izrazilo željo, da bi za jadrnico Elan Impression 384 po postopku predfabriciranega tika vnaprej izdelali tikovo palubo, ki ne bi bila privita na podlago, temveč lepljena s pomočjo lepilne mase Sikaflex. Pri starem sistemu so vsako letvico na pohodnem delu posebej obdelali, prilepili na palubo in privili. Vijak so prekrili z leseno krpo. Pri novem sistemu tikovo oblogo izdelamo na šabloni in jo kot predfabrikat po zelo enostavnem in hitrem postopku montiramo na plovilo. Predfabricirane tikove obloge lahko v prihodnje popolnoma zamenjajo klasičen način polaganja; take palube pa so izdelane mnogo hitreje, veliko bolj kakovostno in to s pomočjo nižje kvalificiranih delavcev. Bistvo predlaganega postopka je, da oblogo na plovilo le montiramo, da je ne izdelujemo na njem, ter tako zelo skrajšamo proizvodni čas.

Jezik:Slovenski jezik
Ključne besede:les, lesna industrija, obrt, navtika, tik, tikova obloga, predfabrikat
Vrsta gradiva:Diplomsko delo
Tipologija:2.11 - Diplomsko delo
Organizacija:BF - Biotehniška fakulteta
Kraj izida:Ljubljana
Založnik:[M. Bijol]
Leto izida:2007
Št. strani:VIII, 46 f., [6 f. pril.]
PID:20.500.12556/RUL-205 Povezava se odpre v novem oknu
UDK:674:629.125.1
COBISS.SI-ID:1508233 Povezava se odpre v novem oknu
Datum objave v RUL:11.07.2014
Število ogledov:2310
Število prenosov:393
Metapodatki:XML DC-XML DC-RDF
:
Kopiraj citat
Objavi na:Bookmark and Share

Sekundarni jezik

Jezik:Angleški jezik
Naslov:Modelling and constructing of teak deck : graduation thesis (higher professional studies)
Izvleček:
Elan Marine, a yacht producer, expressed a wish to produce a new type of teak wood deck for its Elan Impression 384 yacht. The deck was to be made using the prefabricated teak wood procedure where teak wood panels would not be screwed into the underlying base but rather glued on it by the Sikaflex adhesive. The established classic approach implied every deck panel board to be measured and fitted separately, glued on the surface and finally screwed on the deck base. Each screw was then covered by a wooden patch. Under the new system the teak wood panel boards are first measured and cut on the basis of a deck model, and then fitted on the vessel deck following a simple and quick procedure. In the future such prefabricated teak wood panels could entirely replace the established classic approach since their production is faster, of higher quality and can be done by workers of lower skill levels. The essence of the suggested new approach is the use of prefabricated wooden deck panels that are simply fitted on the vessel, thus replacing the classic approach where the wooden deck was actually made in-situ on board of each yacht.

Ključne besede:wood, woodworking industry, craft, nautic, teak wood deck, panel boards, prefabricated

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Nazaj