Optimization method of multi-parameter coupling for a hydraulic rolling reshaper based on factorial design

Li, Hongfei (avtor), Luo, Min (avtor), Xu, Tingting (avtor), Li, Qiaozhen (avtor), Hou, Yanming (avtor)

A hydraulic rolling reshaper is an advanced shaping technology with superior protection for casings, and the structural parameters of the reshaper affect its shaping effect on deformed casing directly. To improve the shaping capacity of the reshaper, a multi-parameter coupling optimization method of hydraulic rolling reshaper is proposed to optimize the design of the factors with significant influence under the premise of screening multi-structural parameters. In this paper, according to the working principle of the reshaper, considering the contact nonlinearity between the hydraulic rolling reshaper and deformed casing, as well as the material nonlinearity of the casing, a parametric finite element model of the hydraulic rolling reshaper repairing the shrinkage deformation of casings was developed. The remarkable factors were screened by factorial design, the sample points were generated by optimal Latin hyper-cube design (OLHD), and the response surface models were established by stepwise regression. Therefore, with the maximum plastic deformation of casings as the objective function, the maximum equivalent stress, residual stress, and the plastic deformation of casings as the constrained conditions, an optimized mathematical model for a reshaper was constructed, and the genetic algorithm (GA) is performed to obtain the optimal combination of parameters. The results showed that the optimal reshaper made the shaping process safe and effective, the plastic deformation of casings after single shaping was increased by 11.38 %, and the shaping effect was better (96.48 %), which can effectively improve the safety performance and shaping ability of the reshaper.

• Jezik: Angleški jezik
• Ključne besede: hydraulic rolling reshaper, structural optimization, factorial design, orthogonal test
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: FS - Fakulteta za strojništvo
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Leto izida: 2023
• Št. strani: Str. 483-496
• Številčenje: Vol. 69, no. 11/12
• PID: 20.500.12556/RUL-154133
• UDK: 621.22
• ISSN pri članku: 0039-2480
• DOI: 10.5545/sv-jme.2023.627
• COBISS.SI-ID: 182612739
• Datum objave v RUL: 26.01.2024

Gradivo je del revije

• Naslov: Strojniški vestnik
• Skrajšan naslov: Stroj. vestn.
• Založnik: Zveza strojnih inženirjev in tehnikov Slovenije [etc.], = Association of Mechanical Engineers and Technicians of Slovenia [etc.
• ISSN: 0039-2480
• COBISS.SI-ID: 762116

Licence

• Licenca: CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by/4.0/deed.sl
• Opis: To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

• Jezik: Slovenski jezik
• Naslov: Metoda za optimizacijo večparametrske sklopitve pri hidravlični valjalni oblikovalni napravi na podlagi faktorske zasnove
• Ključne besede: hidravlična valjalna oblikovalna naprava, optimizacija konstrukcije, faktorska zasnova, ortogonalni test, metoda odzivnih površin, obnova vrtin

Projekti

• Financer: Drugi - Drug financer ali več financerjev
• Program financ.: National Natural Science Foundation of China
• Številka projekta: 51674088

• Financer: Drugi - Drug financer ali več financerjev
• Program financ.: Natural Science Foundation of Heilongjiang
• Številka projekta: LH2021E011