izpis_h1_title_alt

Design and optimization of an umbrella-type shield based on 3D CFD simulation technology
ID Li, Longfei (Avtor), ID He, Xin (Avtor), ID Jiao, Taowei (Avtor), ID Xiao, Yumeng (Avtor), ID Wei, Xipan (Avtor), ID Li, Wei (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (3,82 MB)
MD5: AE5725F833095C168D0147FDB46F92AB
URLURL - Izvorni URL, za dostop obiščite https://www.sv-jme.eu/sl/article/design-and-optimization-of-an-umbrella-type-shield-based-on-3d-cfd-simulation-technology/ Povezava se odpre v novem oknu

Izvleček
Mechanical shields can effectively alleviate the problems of low pesticide utilization and severe environmental pollution. This manuscript uses a computational fluid dynamics (CFD) method to investigate the anti-drift mechanism of mechanical shields, study the airflow forms around them, and establish an accurate simulation model. The aerodynamic characteristics of six shields were studied, and their anti-drift effect was compared. Then, the size and working parameters were optimized using the response surface methodology (RSM). Mechanical shields can significantly improve the fog droplet deposition rate (DR) compared with the conventional spray method (no shield), among which the umbrella-type shield has the best effect; optimizing the size and selecting suitable working parameters can increase the DR to 77.31 %. The field trial showed that the DR of the conventional spray method was reduced by 31.9 % at 5 m/s compared with 3 m/s, while the DR of the shield spray method was reduced by only 3.6 % at 5 m/s compared with 3 m/s, which proved the excellent performance of the mechanical shields. The field trial results were consistent with the CFD simulation, and the relative deviation of the DR between the two was within 4 %, so the accuracy and reliability of the CFD simulation model were proved.

Jezik:Angleški jezik
Ključne besede:mechanical shield, anti-drift, CFD simulation
Vrsta gradiva:Članek v reviji
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Status publikacije:Objavljeno
Različica publikacije:Objavljena publikacija
Leto izida:2023
Št. strani:11 str.
Številčenje:Vol. 69, no. 9/10
PID:20.500.12556/RUL-151864 Povezava se odpre v novem oknu
UDK:004.4
ISSN pri članku:0039-2480
DOI:10.5545/sv-jme.2023.644 Povezava se odpre v novem oknu
COBISS.SI-ID:168834563 Povezava se odpre v novem oknu
Datum objave v RUL:23.10.2023
Število ogledov:378
Število prenosov:16
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
:
Kopiraj citat
Objavi na:Bookmark and Share

Gradivo je del revije

Naslov:Strojniški vestnik
Skrajšan naslov:Stroj. vestn.
Založnik:Zveza strojnih inženirjev in tehnikov Slovenije [etc.], = Association of Mechanical Engineers and Technicians of Slovenia [etc.
ISSN:0039-2480
COBISS.SI-ID:762116 Povezava se odpre v novem oknu

Licence

Licenca:CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

Jezik:Slovenski jezik
Naslov:Zasnova in optimizacija dežnikastega ščita s tehnologijo simulacij 3D CFD
Ključne besede:mehanski ščit, mehanizem za preprečevanje drifta, računalniška dinamika fluidov, aerodinamične lastnosti, stopnja odlaganja kapljic, metoda odzivnih površin

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Nazaj