Vaš brskalnik ne omogoča JavaScript!
JavaScript je nujen za pravilno delovanje teh spletnih strani. Omogočite JavaScript ali pa uporabite sodobnejši brskalnik.
Nacionalni portal odprte znanosti
Odprta znanost
DiKUL
slv
|
eng
Iskanje
Brskanje
Novo v RUL
Kaj je RUL
V številkah
Pomoč
Prijava
The nickel aluminide coatings obtained on small holes produced with the EDD method
ID
Trajer, Marcin
(
Avtor
),
ID
Pyclik, Łukasz
(
Avtor
),
ID
Sobiecki, Jerzy Robert
(
Avtor
)
PDF - Predstavitvena datoteka,
prenos
(4,55 MB)
MD5: BFA7C2DC576C422AE9C5083D9C9A76A9
URL - Izvorni URL, za dostop obiščite
https://www.sv-jme.eu/sl/article/the-nickel-aluminide-coatings-obtained-on-small-holes-produced-by-edd-method/
Galerija slik
Izvleček
Recently, airplane travel has become more affordable and thus more common. This has required engineers and scientists to spend thousands of hours on the development of new material and production technologies. High-pressure turbine (HPT) components are the most heavily loaded parts from the thermal, mechanical, and corrosion points of view. Therefore, both the material from which blades and vanes are cast as well as protective coatings are being constantly developed. Better material translates into longer and safer engine operation. Coatings maintain material structures within aggressive environments. However, despite the wide scope of development, there are areas that have not been investigated, one of which is electro-discharge drilling (EDD) machined cooling holes surface and its influence on environmental coating durability. In this paper, the EDD process impact on coating durability is shown. Process residuals, such as redeposited material and recast layers, result in coating inclusions. Oxidation testing also shows the relationship between the cooling hole diameter and coating durability.
Jezik:
Angleški jezik
Ključne besede:
EDD method
,
nickel aluminide
,
turbine blades
,
durability
,
jet engines
Vrsta gradiva:
Članek v reviji
Tipologija:
1.01 - Izvirni znanstveni članek
Organizacija:
FS - Fakulteta za strojništvo
Status publikacije:
Objavljeno
Različica publikacije:
Objavljena publikacija
Leto izida:
2022
Št. strani:
12 str.
Številčenje:
Vol. 68, no. 10
PID:
20.500.12556/RUL-142723
UDK:
621.9.048
ISSN pri članku:
0039-2480
DOI:
10.5545/sv-jme.2022.169
COBISS.SI-ID:
130434563
Datum objave v RUL:
22.11.2022
Število ogledov:
715
Število prenosov:
60
Metapodatki:
Citiraj gradivo
Navadno besedilo
BibTeX
EndNote XML
EndNote/Refer
RIS
ABNT
ACM Ref
AMA
APA
Chicago 17th Author-Date
Harvard
IEEE
ISO 690
MLA
Vancouver
:
Kopiraj citat
Objavi na:
Gradivo je del revije
Naslov:
Strojniški vestnik
Skrajšan naslov:
Stroj. vestn.
Založnik:
Zveza strojnih inženirjev in tehnikov Slovenije [etc.], = Association of Mechanical Engineers and Technicians of Slovenia [etc.
ISSN:
0039-2480
COBISS.SI-ID:
762116
Licence
Licenca:
CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:
http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:
To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.
Sekundarni jezik
Jezik:
Slovenski jezik
Naslov:
Priprava prevlek iz nikljevega aluminida na majhnih luknjah po postopku EDD
Ključne besede:
elektroerozijsko vrtanje
,
visokotlačne turbine
,
prevleke
Podobna dela
Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:
Nazaj