Podrobno

Comparing surface topography parameters of rough surfaces obtained with spectral moments and deterministic methods
ID Kalin, Mitjan (Avtor), ID Pogačnik, Aljaž (Avtor), ID Etsion, I. (Avtor), ID Raeymaekers, B. (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (589,85 KB)
MD5: 28FF560BDA1A917F5C590744C75ECC64
URLURL - Izvorni URL, za dostop obiščite https://www.sciencedirect.com/science/article/pii/S0301679X15004156?via%3Dihub Povezava se odpre v novem oknu

Izvleček
Understanding contact between rough surfaces is of critical importance to the design of many engineering applications. Contact models rely on material properties and surface topography of the contacting surfaces as input parameters. Hence, the relevance of the contact models is dependent on their inherent assumptions and the accuracy with which the input parameters are determined. We have evaluated the difference between the surface topography parameters calculated with a statistical and deterministic approach for actual engineering surfaces. We have found topography values that change up to 300% depending on the method used, and attribute this to the stringent definition of an asperity-peak in the case of deterministic analysis as opposed to statistical analysis, which not only considers asperity-peaks but also asperity-shoulders.

Jezik:Angleški jezik
Ključne besede:surface topography, spectral moments, deterministic analysis
Vrsta gradiva:Članek v reviji
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Status publikacije:Objavljeno
Različica publikacije:Recenzirani rokopis
Leto izida:2016
Št. strani:Str. 137-141
Številčenje:Vol. 93, pt. A
PID:20.500.12556/RUL-106738 Povezava se odpre v novem oknu
UDK:620.1(045)
ISSN pri članku:0301-679X
DOI:10.1016/j.triboint.2015.09.013 Povezava se odpre v novem oknu
COBISS.SI-ID:14288923 Povezava se odpre v novem oknu
Datum objave v RUL:14.03.2019
Število ogledov:1608
Število prenosov:812
Metapodatki:XML DC-XML DC-RDF
:
KALIN, Mitjan, POGAČNIK, Aljaž, ETSION, I. in RAEYMAEKERS, B., 2016, Comparing surface topography parameters of rough surfaces obtained with spectral moments and deterministic methods. Tribology international [na spletu]. 2016. Vol. 93, no. pt. A, p. 137–141. [Dostopano 26 april 2025]. DOI 10.1016/j.triboint.2015.09.013. Pridobljeno s: https://repozitorij.uni-lj.si/IzpisGradiva.php?lang=slv&id=106738
Kopiraj citat
Objavi na:Bookmark and Share

Gradivo je del revije

Naslov:Tribology international
Skrajšan naslov:Tribol. int.
Založnik:Elsevier
ISSN:0301-679X
COBISS.SI-ID:26558976 Povezava se odpre v novem oknu

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:topografija površin, spektrarni momenti, deterministične analize

Projekti

Financer:Drugi - Drug financer ali več financerjev
Številka projekta:3211-09-100049
Naslov:European Social Fund

Podobna dela

Podobna dela v RUL:
  1. Dynamic measurements using FDM 3D-printed embedded strain sensors
  2. Upgrading the printing quality of budged FDM 3D printer
  3. Quality of polycarbonate joint welded with resistive wire
  4. System for automatic removal of products from a 3D printer
  5. Mechanical properties of 3D printed part from PLA material
Podobna dela v drugih slovenskih zbirkah:
  1. Analysis of the influence of the charging system on the performance by downsizing tgdi engine
  2. ANALYSIS OF THE INFLUENCE OF ROAD ACCESS POINTS DENSITY TO TRAFFIC SAFETY
  3. From idea to innovation with use of appropriate technologies
  4. The influence of binder type on the properties of 3d printed polymer bonded magnets
  5. PREPARING MODELS FOR 3D - PRINTING

Nazaj