Thermo-hydraulic evaluation of oscillating-flow shell-and-tube-like regenerators for (elasto)caloric cooling

Ahčin, Žiga (avtor), Liang, Jierong (avtor), Engelbrecht, Kurt (avtor), Tušek, Jaka (avtor)

The development of novel regenerators for caloric cooling applications requires a detailed evaluation of their thermo-hydraulic properties. Structures similar to shell-and-tube heat exchangers are one of the most promising geometries for elastocaloric technology since they exhibit high thermal performance and can be applied under compressive loading to overcome the limited fatigue life of elastocaloric materials normally experienced in tension. However, thermo-hydraulic properties of shell-and-tube-like structures at the conditions relevant for caloric cooling applications (oscillating counter-flow regime at low Reynolds numbers (<2000) and water as a heat transfer fluid) have not yet been characterized. In this paper, comprehensive oscillating-flow passive experimental characterization and numerical modeling were used to determine their thermo-hydraulic performance. By varying the tube wall thickness, the tube/rod diameter, the spacing between the tubes/rods, and the channel height (baffle distance), nine different regenerators were assembled and analyzed for their thermal effectiveness, convective heat transfer and friction losses. New Nusselt number and friction factor empirical correlations were developed and compared with packed beds and parallel plate regenerators (as two most widely applied regenerator geometries in caloric cooling). We show that shell-and-tube(rod)-like regenerators can reach relatively high effectiveness (up to 0.92) and can present an excellent compromise between heat transfer and pressure drop properties. The shell-and-tube-like geometry can serve as a highly efficient (elasto)caloric regenerator, but dense packing with a small(er) hydraulic diameter is required to further increase the convective heat transfer coefficients and the NTU values. The obtained results should serve as guidelines for overall optimization of compression-loaded shell-and-tube-like elastocaloric regenerator.

• Jezik: Angleški jezik
• Ključne besede: heat regenerator, shell-and-tube heat exchanger, elastocaloric cooling, thermal effectiveness, Nusselt number, friction factor
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: FS - Fakulteta za strojništvo
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Leto izida: 2021
• Št. strani: 15 str.
• Številčenje: Vol. 190, art. 116842
• PID: 20.500.12556/RUL-125551
• UDK: 519.876.5:621.57(045)
• ISSN pri članku: 1359-4311
• DOI: 10.1016/j.applthermaleng.2021.116842
• COBISS.SI-ID: 57027843
• Datum objave v RUL: 24.03.2021

AHČIN, Žiga, LIANG, Jierong, ENGELBRECHT, Kurt in TUŠEK, Jaka, 2021, Thermo-hydraulic evaluation of oscillating-flow shell-and-tube-like regenerators for (elasto)caloric cooling. Applied thermal engineering [na spletu]. 2021. Vol. 190,  116842. [Dostopano 6 april 2025]. DOI 10.1016/j.applthermaleng.2021.116842. Pridobljeno s: https://repozitorij.uni-lj.si/IzpisGradiva.php?lang=slv&id=125551

Gradivo je del revije

• Naslov: Applied thermal engineering
• Skrajšan naslov: Appl. therm. eng.
• Založnik: Elsevier
• ISSN: 1359-4311
• COBISS.SI-ID: 1861910

Licence

• Licenca: CC BY-NC-ND 4.0, Creative Commons Priznanje avtorstva-Nekomercialno-Brez predelav 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by-nc-nd/4.0/deed.sl
• Opis: Najbolj omejujoča licenca Creative Commons. Uporabniki lahko prenesejo in delijo delo v nekomercialne namene in ga ne smejo uporabiti za nobene druge namene.

Sekundarni jezik

• Jezik: Slovenski jezik
• Ključne besede: regenerator toplote, kotelni prenosnik toplote, elastokalorično hlajenje, učinkovitost, Nusseltovo število, faktor trenja