izpis_h1_title_alt

Overheating reduction in lightweight framed buildings with application of phase change materials
Zavrl, Eva (Avtor), Zupanc, Gašper (Avtor), Stritih, Uroš (Avtor), Dovjak, Mateja (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (870,75 KB)
URLURL - Izvorni URL, za dostop obiščite https://www.sv-jme.eu/article/overheating-reduction-in-lightweight-framed-buildings-with-application-of-phase-change-materials/ Povezava se odpre v novem oknu

Izvleček
The trend of lightweight framed building structures is gaining in popularity. Due to lower accumulation capability and thermal stability, buildings might be inclined to higher risk of overheating. The purpose of this study is to investigate overheating in lightweight framed buildings from the aspect of thermal comfort and energy efficiency in cooling season. Single-family house was modelled using DesignBuilder and located in moderate climate (Ljubljana, Slovenia). Heavyweight structure was compared to lightweight structure coupled with all 14 variations of phase change materials (PCM). Different strategies of PCM encapsulation (microencapsulated plasterboards, macroencapsulated additional layer), melting points (23 °C, 24 °C, 25 °C, 26 °C, 27 °C), capacities (M182, M91 M51, M27) and thicknesses (125 mm, 250 mm) of PCM were investigated and compared. The best passive solution was primarily evaluated based on the thermal comfort characteristics: average zone operative temperature (To) bends in cooling season. Secondarily, the additional energy needed for cooling within each solution was compared to the maximum allowed annual energy consumed for cooling specified in legislation. Consequently, the most influential parameter was the melting point of the PCM structure. Based on the chosen criteria, the overheating was significantly reduced using macroencapsulated layer with melting point of 24 °C and minimum capacity of M51 (max. To 26.3 °C). Heavyweight structure enabled lower To (27.1 °C) in the building compared to microencapsulated plasterboard solution with melting point at 23°C and thickness of 250 mm (28.8 °C). Correctly designed passive solution can be used for the improvement of the design strategy and legislation towards overheating prevention.

Jezik:Angleški jezik
Ključne besede:overheating, lightweight framed buildings, phase change materials, thermal comfort, energy efficiency
Vrsta gradiva:Članek v reviji (dk_c)
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Leto izida:2020
Št. strani:str. 3-14
Številčenje:Vol. 66, no. 1
UDK:620.9(045)
ISSN pri članku:0039-2480
DOI:10.5545/sv-jme.2019.6244 Povezava se odpre v novem oknu
COBISS.SI-ID:17015835 Povezava se odpre v novem oknu
Število ogledov:149
Število prenosov:150
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
 
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
:
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Gradivo je del revije

Naslov:Strojniški vestnik
Skrajšan naslov:Stroj. vestn.
Založnik:Zveza strojnih inženirjev in tehnikov Slovenije [et al.], = Association of Mechanical Engineers and Technicians of Slovenia [et al.]
ISSN:0039-2480
COBISS.SI-ID:762116 Povezava se odpre v novem oknu

Gradivo je financirano iz projekta

Financer:ARRS - Agencija za raziskovalno dejavnost Republike Slovenije (ARRS)
Številka projekta:P2-0158
Naslov:Gradbene konstrukcije in gradbena fizika

Financer:ARRS - Agencija za raziskovalno dejavnost Republike Slovenije (ARRS)
Številka projekta:P2-0223
Naslov:Prenos toplote in snovi

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:pregrevanje, lahka gradnja, fazno spremenljive snovi, toplotno ugodje, raba energije

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj