A method for correcting the high-frequency mechanical vibration effects in the dynamic calibration of pressure measurement systems using a shock tube

Svete, Andrej (avtor), Amer, Eynas (avtor), Jönsson, Gustav (avtor), Kutin, Jože (avtor), Arrhén, Fredrik (avtor)

The extremely rapid reflection of a shock wave from the end wall generated in the shock tube, in addition to the high-frequency content of pressure, inevitably also excites mechanical vibrations. These can potentially produce acceleration-induced spurious signals as part of the dynamic output of the pressure measurement system being calibrated. This paper proposes and evaluates a method for correcting the frequency response of a pressure measurement system obtained with a calibration using a shock tube for the acceleration-induced errors due to vibrations. The proposed method is based on the predetermined frequency response of the pressure measurement system to the accelerations and simultaneous measurements of the vibration accelerations of the pressure sensor during its calibration in the shock tube. The acceleration-induced errors were corrected for a piezoelectric pressure measurement system calibrated in a diaphragmless shock tube developed at the National laboratory for pressure and vacuum at RISE Research Institutes of Sweden, where different vibrational conditions were induced by changing the initial driver pressure, while keeping the initial driven pressure constant. The uncertainty of the correction of the frequency response of the piezoelectric pressure measurement system being calibrated was determined by considering the uncertainty contributions of the measured acceleration frequency response of the pressure measurement system, the measured acceleration of the pressure sensor during its calibration in the shock tube, the generated reference end-wall step pressure and the repeatability of the correction. The results show that the proposed method effectively eliminates acceleration-induced errors in the sensitivity and phase frequency responses of an acceleration-sensitive piezoelectric pressure measurement system being calibrated with a shock tube.

• Jezik: Angleški jezik
• Ključne besede: shock tubes, piezoelectric pressure measurement systems, vibrations, acceleration-induced error, frequency response, uncertainty analysis
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: FS - Fakulteta za strojništvo
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Leto izida: 2023
• Št. strani: 13 str.
• Številčenje: Vol. 193, art. 110246
• PID: 20.500.12556/RUL-144655
• UDK: 531.787
• ISSN pri članku: 1096-1216
• DOI: 10.1016/j.ymssp.2023.110246
• COBISS.SI-ID: 144267011
• Datum objave v RUL: 07.03.2023

SVETE, Andrej, AMER, Eynas, JÖNSSON, Gustav, KUTIN, Jože in ARRHÉN, Fredrik, 2023, A method for correcting the high-frequency mechanical vibration effects in the dynamic calibration of pressure measurement systems using a shock tube. Mechanical systems and signal processing [na spletu]. 2023. Vol. 193,  110246. [Dostopano 5 maj 2025]. DOI 10.1016/j.ymssp.2023.110246. Pridobljeno s: https://repozitorij.uni-lj.si/IzpisGradiva.php?lang=slv&id=144655

Gradivo je del revije

• Naslov: Mechanical systems and signal processing
• Skrajšan naslov: Mech. syst. signal process.
• Založnik: Elsevier
• ISSN: 1096-1216
• COBISS.SI-ID: 15296283

Licence

• Licenca: CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by/4.0/deed.sl
• Opis: To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

• Jezik: Slovenski jezik
• Ključne besede: udarne cevi, piezoelektrični merilni sistemi za tlak, vibracije, pogrešek zaradi pospeška, frekvenčni odziv, analiza negotovosti

Projekti

• Financer: ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
• Številka projekta: J2-3054
• Naslov: Napredni sistem udarne cevi za visokofrekvenčno primarno dinamično tlačno umerjanje

• Financer: ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
• Številka projekta: P2-0223
• Naslov: Prenos toplote in snovi