Podrobno

Understanding the friction laws of Amontons and Coulomb by evaluating the real contact area
ID Kalin, Mitjan (Avtor), ID Jan, Petra (Avtor)

.pdfPDF - Predstavitvena datoteka, prenos (3,85 MB)
MD5: 1CD353F11A6DD9968E7E8BF766EDE8FB
URLURL - Izvorni URL, za dostop obiščite https://www.sciopen.com/article/10.26599/FRICT.2025.9440986 Povezava se odpre v novem oknu

Izvleček
Friction is a complex phenomenon that depends on many parameters. Despite this, we still rely on and describe friction in the vast majority of cases with a single value, namely, the coefficient of friction (µ), as first proposed by Amontons in 1699. Later, Coulomb introduced a two-parameter description by separating the adhesive and load-dependent terms. However, experimental evidence that determines under what conditions either of the two historical models is more appropriate has not been investigated in detail. In particular, to take full advantage and achieve better accuracy with the two-parameter equation, the real contact area must be well characterized to determine the constant adhesive component sufficiently and accurately. In this study, we performed sliding experiments and measured friction, but at the same time, we also measured the real contact area with sub-micron lateral resolution, which allowed us to design a two-parameter (Coulomb-type) friction equation. We compared these results with the historical friction models of Amontons and Coulomb to better understand the actual differences between them and how this corresponds to the linearity between the friction force and the normal force, which is a key assumption in the more common and simpler Amontons relation. A strong scaling effect of roughness was observed, as well as the related nonlinearity between the normal load, friction, and real contact area. Under high loads and roughnesses, the one- or two-parameter friction descriptive models differed from experiments by only a few percent, and the variation among them was small in the same range. However, for very low roughnesses and loads (close to the nanoscale region), the two-parameter Coulomb model was required for any relevant friction prediction due to the strong adhesive contribution, while the one-parameter description was not appropriate.

Jezik:Angleški jezik
Ključne besede:real contact area, friction, sliding, Amontons, Coulomb
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Status publikacije:Objavljeno
Različica publikacije:Objavljena publikacija
Leto izida:2024
Št. strani:14 str.
Številčenje:Vol. 13, iss. 1, art. 9440986
PID:20.500.12556/RUL-166909 Povezava se odpre v novem oknu
UDK:531.4
ISSN pri članku:2223-7690
DOI:10.26599/FRICT.2025.9440986 Povezava se odpre v novem oknu
COBISS.SI-ID:218328835 Povezava se odpre v novem oknu
Datum objave v RUL:30.01.2025
Število ogledov:135
Število prenosov:37
Metapodatki:XML DC-XML DC-RDF
:
Kopiraj citat
Objavi na:Bookmark and Share

Gradivo je del revije

Naslov:Friction
Skrajšan naslov:Frict.
Založnik:Tsinghua University Press
ISSN:2223-7690
COBISS.SI-ID:525351449 Povezava se odpre v novem oknu

Licence

Licenca:CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:pravo kontaktno območje, trenje, drsenje

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Nazaj