Vaš brskalnik ne omogoča JavaScript!
JavaScript je nujen za pravilno delovanje teh spletnih strani. Omogočite JavaScript ali pa uporabite sodobnejši brskalnik.
Nacionalni portal odprte znanosti
Odprta znanost
DiKUL
slv
|
eng
Iskanje
Brskanje
Novo v RUL
Kaj je RUL
V številkah
Pomoč
Prijava
Surface quality of AZ91D magnesium alloy after precision milling with coated tools
ID
Korpysa, Jarosław
(
Avtor
),
ID
Kuczmaszewski, Jozef
(
Avtor
),
ID
Zagorski, Ireneusz
(
Avtor
)
PDF - Predstavitvena datoteka,
prenos
(3,01 MB)
MD5: D6ED2CF1B371242B924431E7566309BA
URL - Izvorni URL, za dostop obiščite
https://www.sv-jme.eu/sl/article/surface-quality-of-az91d-magnesium-alloy-after-precision-milling-with-coated-tools/
Galerija slik
Izvleček
This study investigates the surface quality of AZ91D magnesium alloy specimens after precision milling. The milling was conducted with the use of TiB2- and TiAlN-coated carbide end mills. The following variables were used in the milling process: cutting speed vc, feed per tooth fz and axial depth of cut ap. The surface quality was analysed based on surface roughness parameters and Abbott-Firestone curves. The results showed that the surface quality after machining depended on the tool coating type and applied machining parameters; the only exception was the axial depth of cut because changes in its value did not have any significant effect on the obtained surface quality. After precision milling, AZ91D specimens were characterized by very low surface roughness parameters. The impact of machining conditions was also evaluated with ANOVA analysis, which confirmed the significant effect of cutting speed and feed per tooth. It also indicated the dependence of the roughness parameters on the tool coating type. The tool coating type and machining conditions did not have any significant effect on the Abbott-Firestone curves. Despite the changes applied, the shape of the curves remained similar. The obtained results provide both theoretical and practical knowledge about the achievable surface roughness of AZ91D magnesium alloy specimens after precision milling.
Jezik:
Angleški jezik
Ključne besede:
precision milling
,
surface quality
,
Abbott-Firestone curve
,
ANOVA
,
coated tools
Vrsta gradiva:
Članek v reviji
Tipologija:
1.01 - Izvirni znanstveni članek
Organizacija:
FS - Fakulteta za strojništvo
Status publikacije:
Objavljeno
Različica publikacije:
Objavljena publikacija
Leto izida:
2023
Št. strani:
Str. 497-508
Številčenje:
Vol. 69, no. 11/12
PID:
20.500.12556/RUL-154134
UDK:
621.7+621.9
ISSN pri članku:
0039-2480
DOI:
10.5545/sv-jme.2023.651
COBISS.SI-ID:
182620931
Datum objave v RUL:
26.01.2024
Število ogledov:
165
Število prenosov:
7
Metapodatki:
Citiraj gradivo
Navadno besedilo
BibTeX
EndNote XML
EndNote/Refer
RIS
ABNT
ACM Ref
AMA
APA
Chicago 17th Author-Date
Harvard
IEEE
ISO 690
MLA
Vancouver
:
Kopiraj citat
Objavi na:
Gradivo je del revije
Naslov:
Strojniški vestnik
Skrajšan naslov:
Stroj. vestn.
Založnik:
Zveza strojnih inženirjev in tehnikov Slovenije [etc.], = Association of Mechanical Engineers and Technicians of Slovenia [etc.
ISSN:
0039-2480
COBISS.SI-ID:
762116
Licence
Licenca:
CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:
http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:
To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.
Sekundarni jezik
Jezik:
Slovenski jezik
Naslov:
Kakovost površin magnezijeve zlitine AZ91D po natančnem rezkanju z oslojenimi orodji
Ključne besede:
natančno rezkanje
,
kakovost površin
,
krivulja Abbott-Firestone
,
ANOVA
,
oslojena orodja
Projekti
Financer:
Drugi - Drug financer ali več financerjev
Program financ.:
Mechanical Engineering Discipline Fund of Lublin University of Technology
Številka projekta:
FD-20/IM-5/060
Podobna dela
Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:
Nazaj