Vaš brskalnik ne omogoča JavaScript!
JavaScript je nujen za pravilno delovanje teh spletnih strani. Omogočite JavaScript ali pa uporabite sodobnejši brskalnik.
Repozitorij Univerze v Ljubljani
Nacionalni portal odprte znanosti
Odprta znanost
DiKUL
slv
|
eng
Iskanje
Brskanje
Novo v RUL
Kaj je RUL
V številkah
Pomoč
Prijava
Podrobno
Machining of hard-to-cut AISI 4462 duplex stainless steel with an environmentally friendly approach with vortex tube
ID
Sönmez, Fikret
(
Avtor
)
PDF - Predstavitvena datoteka,
prenos
(2,48 MB)
MD5: 46A2FDD22EDBA6B41F37F60D24BFDF19
URL - Izvorni URL, za dostop obiščite
https://www.sv-jme.eu/sl/article/machining-of-hard-to-cut-aisi-4462-duplex-stainless-steel-with-an-environmentally-friendly-approach-with-vortex-tube/
Galerija slik
Izvleček
Machining is a manufacturing process that can be used to produce precision machine parts and has many advantages. The first is the ability to achieve superior surface quality. Tool wear is an inevitable phenomenon that occurs during machining. It is affected by many machining conditions; therefore, this process needs to be monitored and controlled. In this study, tool wear and surface roughness tests were carried out on AISI 4462 duplex stainless-steel materials, known to be a hard-to-cut material. For this purpose, tool wear and surface roughness analyses were implemented by using the environmentally friendly vortex tube cooling system in addition to wet turning conditions for the first time. For both methods, experiments were conducted at a 1 mm depth of cut, 120 m/min cutting speed, and 0.1 mm/rev feed with a 90 mm cutting length for each pass. Both tool wear and surface roughness were examined at the end of each pass. The analysis showed that wet turning gave better results in terms of tool life (19.8 minutes of tool life) compared to 11.1 minutes of tool life in vortex turning. In contrast, the surface roughness values differed up to two times in some experiments, and the vortex tube experiments gave better surface roughness values in all passes. In addition, the vortex tube experiments showed less built-up-edge (BUE) formation than the wet-turning experiments.
Jezik:
Angleški jezik
Ključne besede:
vortex tube
,
machining
,
duplex stainless steel
,
tool life
,
surface roughness
Vrsta gradiva:
Članek v reviji
Tipologija:
1.01 - Izvirni znanstveni članek
Organizacija:
FS - Fakulteta za strojništvo
Status publikacije:
Objavljeno
Različica publikacije:
Objavljena publikacija
Leto izida:
2023
Št. strani:
Str. 308-316
Številčenje:
Vol. 69, no. 7/8
PID:
20.500.12556/RUL-148933
UDK:
621.91:669.14
ISSN pri članku:
0039-2480
DOI:
10.5545/sv-jme.2023.578
COBISS.SI-ID:
159320835
Datum objave v RUL:
01.09.2023
Število ogledov:
1462
Število prenosov:
68
Metapodatki:
Citiraj gradivo
Navadno besedilo
BibTeX
EndNote XML
EndNote/Refer
RIS
ABNT
ACM Ref
AMA
APA
Chicago 17th Author-Date
Harvard
IEEE
ISO 690
MLA
Vancouver
:
Kopiraj citat
Objavi na:
Gradivo je del revije
Naslov:
Strojniški vestnik
Skrajšan naslov:
Stroj. vestn.
Založnik:
Zveza strojnih inženirjev in tehnikov Slovenije [etc.], = Association of Mechanical Engineers and Technicians of Slovenia [etc.
ISSN:
0039-2480
COBISS.SI-ID:
762116
Licence
Licenca:
CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:
http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:
To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.
Sekundarni jezik
Jezik:
Slovenski jezik
Naslov:
Do okolja prijazen pristop k obdelavi težje odrezovalnega dupleksnega nerjavnega jekla AISI 4462 z vrtinčno cevjo
Ključne besede:
vrtinčna cev
,
obdelava z odrezavanjem
,
dupleksno nerjavno jeklo
,
obstojnost orodja
,
površinska hrapavost
Podobna dela
Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:
Nazaj