Vaš brskalnik ne omogoča JavaScript!
JavaScript je nujen za pravilno delovanje teh spletnih strani. Omogočite JavaScript ali pa uporabite sodobnejši brskalnik.
Nacionalni portal odprte znanosti
Odprta znanost
DiKUL
slv
|
eng
Iskanje
Brskanje
Novo v RUL
Kaj je RUL
V številkah
Pomoč
Prijava
Selection of the most suitable material handling system in production
ID
Berlec, Tomaž
(
Avtor
),
ID
Tanšek, Blaž
(
Avtor
),
ID
Kušar, Janez
(
Avtor
)
PDF - Predstavitvena datoteka,
prenos
(441,49 KB)
MD5: D73CD28A4A8B9B288576A4B6E874C95C
Galerija slik
Izvleček
When building a new company or optimising an existing one, material handling (MH) is often forgotten. Therefore, the paper presents a decision tree, on the basis of which it is possible to select the most suitable MH system by simulation depending on the selected production parameters. Such a simulation can greatly facilitate the selection of the most suitable MH system which will ensure minimal time consumption and still acceptable costs. To perform the simulation, a generalised production system model for 5 different MH systems was created in the FlexSim software, with which 32 different scenarios could be simulated depending on the selected production parameters, tested in a production facility of injection moulded components for the automotive industry. The data obtained from the simulations were then used to analyse the influence of the selected parameters on possible MH systems. For all potential scenarios, the solutions of which are acceptable for MH, a cost-benefit analysis was performed. Based on the analysis, a difference of 75 % between the most and least favourable scenarios was established.
Jezik:
Angleški jezik
Ključne besede:
production
,
material handling systems
,
simulation
,
optimisation
,
cost-benefit analysis
Vrsta gradiva:
Članek v reviji
Tipologija:
1.01 - Izvirni znanstveni članek
Organizacija:
FS - Fakulteta za strojništvo
Status publikacije:
Objavljeno
Različica publikacije:
Objavljena publikacija
Leto izida:
2021
Št. strani:
Str. 64-75
Številčenje:
Vol. 20, no. 1
PID:
20.500.12556/RUL-125233
UDK:
658.2/.5(045)
ISSN pri članku:
1726-4529
DOI:
10.2507/IJSIMM20-1-542
COBISS.SI-ID:
54449411
Datum objave v RUL:
09.03.2021
Število ogledov:
1013
Število prenosov:
193
Metapodatki:
Citiraj gradivo
Navadno besedilo
BibTeX
EndNote XML
EndNote/Refer
RIS
ABNT
ACM Ref
AMA
APA
Chicago 17th Author-Date
Harvard
IEEE
ISO 690
MLA
Vancouver
:
Kopiraj citat
Objavi na:
Gradivo je del revije
Naslov:
International journal of simulation modelling
Skrajšan naslov:
Int. j. simul. model.
Založnik:
DAAAM International Vienna
ISSN:
1726-4529
COBISS.SI-ID:
8008982
Sekundarni jezik
Jezik:
Slovenski jezik
Ključne besede:
proizvodnja
,
rokovanje z materialom
,
simulacija
,
optimizacija
,
analiza koristi
,
analiza stroškov
Projekti
Financer:
Drugi - Drug financer ali več financerjev
Program financ.:
Ministrstvo za izobraževanje znanost in šport
Številka projekta:
P2-0270
Naslov:
Proizvodni sistemi, laserske tehnologije in spajanje materialov
Podobna dela
Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:
Nazaj