21. Studies on structural, mechanical and erosive wear properties of ZA-27 alloy-based micro-nanocompositesAleksandar Vencl, Mara Kandeva, Elena Zadorozhnaya, Petr Svoboda, Michal Michalec, Aleksandar Milivojević, Uroš Trdan, 2021, original scientific article Keywords: ZA-27 alloy, micro-nanocomposites, compocasting, microstructures, hardness, erosive wear Full text (file, 10,36 MB) This document has more files! More... |
22. Modeling and optimization of finish diamond turning of spherical surfaces based on response surface methodology and cuckoo search algorithmDavorin Kramar, Djordje Cica, 2021, original scientific article Keywords: brass alloy, diamond turning, surface roughness, spherical surface, modeling, optimization, response surface methodology, cuckoo search Full text (file, 1,26 MB) This document has more files! More... |
23. Influence of laser texturing on microstructure, surface and corrosion properties of Ti-6Al-4VMarjetka Conradi, Aleksandra Kocijan, Damjan Klobčar, Matjaž Godec, 2020, original scientific article Keywords: surface texture, Ti-6Al-4V alloy, microstructure, wettability, corrosion Full text (file, 2,80 MB) This document has more files! More... |
24. Surface integrity of heat treatable magnesium alloy AZ80A after cavitation peeningSebastjan Žagar, Hitoshi Soyama, Janez Grum, Roman Šturm, 2022, original scientific article Keywords: magnesium alloy AZ80A, cavitation peening, artificial ageing, residual stresses, microhardness, surface roughness, microstructure Full text (file, 2,35 MB) This document has more files! More... |
25. The influence of cooling rate on microstructure and mechanical properties of AlSi9Cu3Matic Žbontar, Mitja Petrič, Primož Mrvar, 2021, original scientific article Keywords: HPDC, aluminum alloy AlSi9Cu3, cooling rate, solidification processes, mechanical properties Full text (file, 3,34 MB) This document has more files! More... |
26. Determination of Al-2.18Mg-1.92Li alloy's microstructure degradation in corrosive environmentFranjo Kozina, Zdenka Zovko Brodarac, Sandra Brajčinović, Mitja Petrič, 2021, original scientific article Keywords: Al-Mg-Li alloy, solidification sequence, as-cast, solution hardening, microstructure, degradation Full text (file, 4,17 MB) This document has more files! More... |
27. Mechanism of the Mg$_3$Bi$_2$ phase formation in Pb-free aluminum 6xxx alloy with bismuth additionSimon Rečnik, Milan Bizjak, Jože Medved, Peter Cvahte, Blaž Karpe, Aleš Nagode, 2021, original scientific article Keywords: free-machining AA6xxx alloy, bismuth, Mg$_3$Bi$_2$ phase, solidifcation model Full text (file, 5,39 MB) This document has more files! More... |
28. Use of Prandtl operators in simulating the cyclic softening of Inconel 718 under isothermal low-cycle fatigue loadingMichal Bartošák, Marko Nagode, Jernej Klemenc, Karel Doubrava, Domen Šeruga, 2022, original scientific article Keywords: Prandtl operators, low-cycle fatigue, plasticity, nickel-based super-alloy, Inconel 718 Full text (file, 1,17 MB) This document has more files! More... |
29. Homogenisation efficiency assessed with microstructure analysis and hardness measurements in the EN AW 2011 aluminium alloyMaja Vončina, Aleš Nagode, Jože Medved, Irena Paulin, Borut Žužek, Tilen Balaško, 2021, original scientific article Keywords: EN AW 2011 aluminium alloy, thermodynamic equilibrium, intermetallic phases, eutectic, homogenisation, hardness Full text (file, 3,77 MB) This document has more files! More... |
30. The influence of shot peening and artificially ageing aluminium alloy 7075 on corrosion behaviourSebastjan Žagar, Primož Mrvar, Janez Grum, Roman Šturm, 2022, original scientific article Keywords: aluminium alloy 7075, shot peening, ageing temperature, pitting corrosion, cyclic polarisation, intermetallic particles Full text (file, 4,84 MB) This document has more files! More... |