izpis_h1_title_alt

Injection-moulding compounding of PP polymer nanocomposites
Battisti, Markus Gottfried (Avtor), Friesenbichler, Walter (Avtor)

URLURL - Predstavitvena datoteka, za dostop obiščite http://www.dlib.si/details/URN:NBN:SI:doc-HX43NUP7 Povezava se odpre v novem oknu

Izvleček
The objective of this study is the comparison of different compounding techniques and their influence on the Youngs modulus. Both, conventional processing of polymer nanocomposites and processing in the worldwide unique Injection Molding Compounder (PNC-IMC) were evaluated. Additionally the effects of nanofillers on the thermal conductivity of polymer nanocomposites were investigated at various pressures.In comparison to the conventional compounding process, where the compound has to be pelletized and fed into the injection molding machine for the second plasticizing process, the injection molding compounding combines these two processing steps. The material compounding and the subsequent injection molding are done directly by only one plasticizing process by the use of a heated melt line and a melt accumulator. In this study, both of these techniques were used for the production of polymer nanocomposites. This paper shows the different effects of processing techniques, screw speed, counter-pressure and different extruder length on the Youngs modulus and demonstrates that for the improvements a compromise between shear energy input and residence time is essential. The increase of thermal conductivity by using nanofillers compared to the virgin polypropylene is shown. The investigated increase in thermal conductivity should be very interesting for the industry in terms of cycle time reduction in the injection molding process. These very first results give a good overview on both the possibilities and the limitations of the innovative concept of the PNC-IMC. Further studies on the detailed understanding concerning exfoliation and intercalation of layered silicates in polymer melt will be done.

Jezik:Angleški jezik
Ključne besede:injection moulding compounding, polymer nanocomposites, thermal conductivity, exfoliation, intercalation, layered silicates
Vrsta gradiva:Delo ni kategorizirano (r6)
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Leto izida:2013
Št. strani:str. 662-668, SI 135
Številčenje:Vol. 59, no. 11
UDK:621.767:678.7
ISSN pri članku:0039-2480
DOI:10.5545/sv-jme.2012.903 Povezava se odpre v novem oknu
COBISS.SI-ID:13219355 Povezava se odpre v novem oknu
Število ogledov:783
Število prenosov:196
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
 
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
:
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Gradivo je del revije

Naslov:Strojniški vestnik
Skrajšan naslov:Stroj. vestn.
Založnik:Zveza strojnih inženirjev in tehnikov Slovenije [et al.], = Association of Mechanical Engineers and Technicians of Slovenia [et al.]
ISSN:0039-2480
COBISS.SI-ID:762116 Povezava se odpre v novem oknu

Sekundarni jezik

Jezik:Slovenski jezik
Ključne besede:brizgalni kompaunderji, polimerni nanokompoziti, toplotna prevodnost, eksfoliacija, interkalacija, silikati v plasteh

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj