izpis_h1_title_alt

Influence of laser beam guiding and overlapping on residual stress in remelting process
Grum, Janez (Avtor), Šturm, Roman (Avtor)

URLURL - Predstavitvena datoteka, za dostop obiščite http://dx.doi.org/10.1179/174329405X30011 Povezava se odpre v novem oknu

Izvleček
The laser remelting process is a very promising hardening method for ferrous and non-ferrous alloys which do not show a homogeneous microstructural state after being heat treated in a traditional way. Consequently, the alloys concerned do not achieve the required hardness of the surface layer and do notprovide the required wear resistance. The present paper deals with residualstress and strain changes in thin flat specimens of nodular cast iron 500-7 in the laser remelting process. In the process of gradual remelting of the specimen surface, i.e. during its heating and cooling, volume changes in the specimen occur due to thermal and microstructural changes. To find out more about volume changes in the thin surface layer of specimens, the latter were monitored by strain measurement at the lower side of the specimens duringthe remelting process and by residual stress measurement in the thin surface layer after the remelting process. The strain was measured using a resistance rosette, placed on the opposite side of the remelted layer, and the temperature was measured in the same place simultaneously. In laser remelting of a workpiece, such remelting conditions should ensure that a uniform thickness of the modified layer is obtained, in spite of several laserbeam passages across the workpiece surface. Owing to the multiple passageof the laser beam across the workpiece surface, the state of internal stress in the workpiece changes and, consequently, undesired strain may occur.Such strain may result in greater consumption of material and additional machining which, in turn, may result in higher cost of the machined parts. The results obtained confirmed that on the basis of knowing the strain occurring during the remelting process and the residual stress, the process could be successfully optimised. On the basis of knowing the strains occurring during the remelting process and the residual stress, optimal laser surface remelting conditions were chosen, while the method of guiding the laser beam over the surface of the flat samples and the degree of overlap were varied.

Jezik:Angleški jezik
Ključne besede:utrjevanje površin, litine nodularne, vodenje snopa, lasersko vodenje, laser beam guiding, overlapping, remelting
Vrsta gradiva:Delo ni kategorizirano (r6)
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:FS - Fakulteta za strojništvo
Leto izida:2005
Št. strani:str. 27-34
Številčenje:Letn. 21, št. 1
UDK:621.791.9:535.374
ISSN pri članku:0267-0844
COBISS.SI-ID:8182299 Povezava se odpre v novem oknu
Število ogledov:590
Število prenosov:218
Metapodatki:XML RDF-CHPDL DC-XML DC-RDF
 
Skupna ocena:(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
:
Objavi na:AddThis
AddThis uporablja piškotke, za katere potrebujemo vaše privoljenje.
Uredi privoljenje...

Gradivo je del revije

Naslov:Surface engineering
Skrajšan naslov:Surf. eng.
Založnik:Institute of Metals, Wolfson Institute for Surface Engineering
ISSN:0267-0844
COBISS.SI-ID:5326855 Povezava se odpre v novem oknu

Podobna dela

Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:

Komentarji

Dodaj komentar

Za komentiranje se morate prijaviti.

Komentarji (0)
0 - 0 / 0
 
Ni komentarjev!

Nazaj