20.500.12556/RUL-149020 Oblikovno obločno navarjanje TIG s hladno in vročo žico TIG wire arc additive manufacturing with cold and warm wire Uporaba aditivnih tehnologij je v stalnem porastu, saj omogoča izdelavo vedno bolj kompleksnih izdelkov. Poleg tega pa v primerjavi s konvencionalnimi postopki odrezavanja omogoča velike finančne prihranke zaradi manjše uporabe materiala. V diplomskem delu smo uporabljali oblikovno obločno navarjanje z uporabo robotske celice po postopku TIG, ki se v industriji še ne uporablja veliko. V začetni fazi smo izvedli preliminarne teste, kjer smo preizkušali različne parametre in določili najprimernejše parametre za navarjanje sten, iz katerih smo izrezali vzorce. Nato smo izvedli vse potrebne teste in analize, ki smo jih podrobno ovrednotili. Rezultati opravljenih analiz so potrdili, da se trdota materiala ne spreminja. Ugotovili smo, da horizontalni vzorci absorbirajo 42 % (96,6 J proti 166 J) manj energije kot vertikalni pri preizkusu udarne žilavosti in imajo 20 % (174,8 MPa proti 150,3 MPa) višjo mejo plastičnosti pri nateznem preizkusu. Vertikalni vzorci dosežejo 14 % (5,85 kN proti 4,67 kN) višjo maksimalno silo in imajo 312 % (12,81 mm proti 4,19 mm) višji maksimalni raztezek. Usage of additive manufacturing is constantly increasing, as it enables the production of increasingly complex products. In addition, it lowers production costs due to reduced material use, when compared to conventional cutting processes. The experiments for this bachelor’s thesis were carried out using a robotic welding cell for TIG arc welding, which is not yet widely used in industry. The initial phase consisted of preliminary examinations for testing various parameters and determining the most suitable ones for welding multiple layers of welds, from which the samples were cut. The next phase consisted of analyzing and examining the samples and evaluating the results. The results of the analyses confirmed that the hardness of the material did not change. Furthermore, the horizontal samples absorbed 42 % (96,6 J vs 166 J) less energy than the vertical ones during the impact toughness test, and they had a 20 % (174,8 MPa vs 150,3 MPa) higher plasticity limit during the tensile test. The vertical patterns achieved a 14 % (5,85 kN vs 4,67 kN) higher maximum force and had a 312 % (12,81mm vs 4,19mm) higher maximum elongation. varjenje TIG z vročo in hladno žico AISI 304 natezna trdnost udarna žilavost robotsko navarjanje TIG welding with hot and cold wire AISI 304 tensile strength impact strength robotic additive manufacturing true false false Slovenski jezik Angleški jezik Diplomsko delo/naloga 2023-09-02 08:33:44 2023-09-02 08:33:45 2023-10-13 08:40:08 0000-00-00 00:00:00 2023 0 0 0000-00-00 NiDoloceno NiDoloceno NiDoloceno 0000-00-00 0000-00-00 0000-00-00 255676 29400.pdf 29400.pdf 1 6883CCB729E8B1E733F4300391F3CE81 a10fefadfbb4d22c71ffee1a18893b31af8d05627a84451144b09b231d3f4724 a9201846-495a-11ee-af86-0050569b8976 https://repozitorij.uni-lj.si/Dokument.php?lang=slv&id=173402 Fakulteta za strojništvo 0 0 0