20.500.12556/RUL-102457 Tehnologiji hitre izdelave komponent interferometra Technology for rapid manufacturing of interferometer components Cilj diplomske naloge je narediti oz. sestaviti interferometer, ki bi bil natančen, relativno poceni in dovolj kakovosten, da bi se lahko uporabil kot dodaten učni pripomoček v osnovnih ali srednjih šolah za poglobitev znanja o interferometriji, optičnih elementih in hkrati predstaviti različne načine tehnoloških postopkov s katerimi smo izdelali Michelsonov interferometer. Bolj podrobno smo se osredotočili na primerjavo dveh različnih tehnologij s katerima je mogoče izdelati držala in nosila za zrcala, lečo in laser. Pri tem smo bili pozorni na ceno določenega tehnološkega postopka, natančnost končnega izdelka in enostavnost končne kalibracije in nastavljanja interferometra. Cenovno gledano je verzija komponent interferometra narejenih s postopkom 3D-tiska malenkost dražja. Natančnost, ki jo zahteva naprava za delovanje je bila pri komponentih zagotovljena, ne glede na tehnološki postopek. Zmožnost nastavljanja interferenčnega vzorca je lažja s 3D-natisnjenimi nosilci, saj imajo vgrajene matice, preko katerih s pomočjo vijaka nastavljamo zrcalo. Pri aluminijastih nosilcih so navoji vrezani in ob večkratnem nastavljanju se le-ti deformirajo, s tem pa pomik ni tako enakomeren kot pri nosilcu z matico. The objective of this thesis is to build the Michelson interferometer that would be accurate, relatively inexpensive and of such quality that could be used as an additional learning tool in elementary and high schools to deepen the learners’ knowledge of interferometry, optical components and would at the same time present different approaches we took when building this device. We focused on the comparison of two different technologies that are used to make holders for mirrors, lens and laser. We paid particular attention to the price of the chosen technological process, accuracy of the final product and simplicity of the interferometer's final calibration. In terms of price, the interferometer's components made with 3D printing are a bit more expensive. The precision required for the device to work was guaranteed with the components regardless of the technological process. The possibility of adjusting the interference patterns is easier with 3D printed mounts, because they have built-in nuts that enable us to adjust the mirror using a screw. Screw threads are carved in aluminium brackets and can deform if being re-adjusted too many times causing the movement not to be as smooth as with the nut mount. Michelsonov interferometer optične komponente konvencionalni in nekonvencionalni tehnološki postopki 3D-tiskanje in primerjava tehnoloških postopkov Michelson's interferometer optical components conventional and nonconventional technology proceses 3D printing and technology commparison. true false false [A. Krsnik] Slovenski jezik Angleški jezik Diplomsko delo/naloga 2018-08-31 07:45:03 2018-08-31 07:45:11 2023-12-01 08:50:22 0000-00-00 00:00:00 2018 0 0 0000-00-00 NiDoloceno NiDoloceno NiDoloceno 0000-00-00 0000-00-00 0000-00-00 658.5:681.723.26(043.2) 207350 16250907 2108.pdf 2108.pdf 1 9FDF8AD4264AB76D229F97385CC3092A 4371fa884d442e4010bcfb6903c79d099bf5a938e1e39979371e54da93aaa61e 8618b31b-a1b5-11eb-a523-00155dcfd717 https://repozitorij.uni-lj.si/Dokument.php?lang=slv&id=112759 Fakulteta za strojništvo 0 0 0