Vaš brskalnik ne omogoča JavaScript!
JavaScript je nujen za pravilno delovanje teh spletnih strani. Omogočite JavaScript ali pa uporabite sodobnejši brskalnik.
Nacionalni portal odprte znanosti
Odprta znanost
DiKUL
slv
|
eng
Iskanje
Brskanje
Novo v RUL
Kaj je RUL
V številkah
Pomoč
Prijava
An energy-efficient vacuum system as an alternative to the inefficient use of compressed air for the yarn suction gun
ID
Prezelj, Jurij
(
Avtor
),
ID
Novaković, Tadej
(
Avtor
),
ID
Čurović, Luka
(
Avtor
),
ID
Železnik, Anže
(
Avtor
),
ID
Murovec, Jure
(
Avtor
)
PDF - Predstavitvena datoteka,
prenos
(2,60 MB)
MD5: 105BFA210859C49ACDBFFB9B27CA2DBB
URL - Izvorni URL, za dostop obiščite
https://www.tandfonline.com/doi/full/10.1080/00405000.2023.2195978
Galerija slik
Izvleček
The yarn suction gun (YSG) is used to draw the running yarn in the initial phase and when changing the bobbin in a continuous yarn production and is usually operated with compressed air. With a typical overall efficiency of compressed air generation, treatment and delivery, the electrical power requirement increases to over 75 kW just to operate a single YSG. Such high electrical power consumption must be addressed. One of the most effective ways to reduce the cost of compressed air generation and treatment is to replace the existing technology with one that is less energy intensive. Based on centrifugal blowers used in vacuum cleaners, a prototype was built and connected to various mixing chambers. Simulations and measurements were performed to evaluate the tension force acting on the yarn. Research on the use of vacuum for yarn suction is presented. It is estimated that after optimizing the suction by using vacuum, only 20 kW of electrical power will be required for one YSG, halving the cost of the current approach using compressed air generation.
Jezik:
Angleški jezik
Ključne besede:
vacuum suction
,
supersonic vacuum flow
,
energy efficiency
,
yarn suction gun
Vrsta gradiva:
Članek v reviji
Tipologija:
1.01 - Izvirni znanstveni članek
Organizacija:
FS - Fakulteta za strojništvo
Status publikacije:
Objavljeno
Različica publikacije:
Objavljena publikacija
Leto izida:
2024
Št. strani:
Str. 460-470
Številčenje:
Vol. 115, iss. 3
PID:
20.500.12556/RUL-154504
UDK:
621.521
ISSN pri članku:
1754-2340
DOI:
10.1080/00405000.2023.2195978
COBISS.SI-ID:
148150787
Datum objave v RUL:
19.02.2024
Število ogledov:
801
Število prenosov:
38
Metapodatki:
Citiraj gradivo
Navadno besedilo
BibTeX
EndNote XML
EndNote/Refer
RIS
ABNT
ACM Ref
AMA
APA
Chicago 17th Author-Date
Harvard
IEEE
ISO 690
MLA
Vancouver
:
Kopiraj citat
Objavi na:
Gradivo je del revije
Naslov:
The journal of the Textile Institute
Založnik:
Woodhead
ISSN:
1754-2340
COBISS.SI-ID:
520822553
Licence
Licenca:
CC BY-NC-ND 4.0, Creative Commons Priznanje avtorstva-Nekomercialno-Brez predelav 4.0 Mednarodna
Povezava:
http://creativecommons.org/licenses/by-nc-nd/4.0/deed.sl
Opis:
Najbolj omejujoča licenca Creative Commons. Uporabniki lahko prenesejo in delijo delo v nekomercialne namene in ga ne smejo uporabiti za nobene druge namene.
Sekundarni jezik
Jezik:
Slovenski jezik
Ključne besede:
vakuumsko sesanje
,
nadzvočno polnjenje vakuuma
,
energijski izkoristek
,
pištola za sesanje filamentov
Projekti
Financer:
ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
Podobna dela
Podobna dela v RUL:
Podobna dela v drugih slovenskih zbirkah:
Nazaj