Bending moment of mortise-and-tenon joints in a crossed chair base

Hajdarević, Seid (avtor), Obućina, Murčo (avtor), Kitek Kuzman, Manja (avtor), Sandberg, Dick (avtor)

This paper investigated the bending moment of chair base joints. The ultimate bending moments (maximum moment), calculated on the base of the measured maximum applied loads (maximum force), were compared for the front leg and rear leg joints of a chair base. The joints had different angles between the stretcher and the leg (joint angle) as well different tenon lengths (30 mm and 32 mm). The results of the tests indicated that for different test specimen configurations but the same tenon-and-mortise geometry, the maximum force of joints with a smaller value of joint angle (front leg joints) was higher than the force values of joints with a larger angle (rear leg joints) for all tenon lengths. However, the results showed less difference among the calculated bending moments of the analysed sets of joints. A significant difference was not revealed between the bending moments of joints with a smaller value of joint angle and the bending moments of joints with a larger angle for all tenon lengths. A significant difference between the bending moments for the tenon length of 30 mm and tenon length of 32 mm was determined for rear leg joints but not for front leg joints. The presented approach of joint strength analysis through the testing of specimens with different shapes and dimensions are applicable to research and practice

• Jezik: Angleški jezik
• Ključne besede: chair, mortise-and-tenant joint, bending moment, joint angle, tenon length
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: BF - Biotehniška fakulteta
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Datum objave: 01.01.2023
• Leto izida: 2023
• Št. strani: Str. 3-11
• Številčenje: Vol. 74, iss. 1
• PID: 20.500.12556/RUL-146691
• UDK: 684.4.058
• ISSN pri članku: 0012-6772
• DOI: 10.5552/drvind.2023.0004
• COBISS.SI-ID: 147831555
• Datum objave v RUL: 07.06.2023

HAJDAREVIĆ, Seid, OBUĆINA, Murčo, KITEK KUZMAN, Manja in SANDBERG, Dick, 2023, Bending moment of mortise-and-tenon joints in a crossed chair base. Drvna industrija : Znanstveno stručni časopis za pitanja drvne tehnologije [na spletu]. 2023. Vol. 74, no. 1, p. 3–11. [Dostopano 11 april 2025]. DOI 10.5552/drvind.2023.0004. Pridobljeno s: https://repozitorij.uni-lj.si/IzpisGradiva.php?lang=slv&id=146691

Gradivo je del revije

• Naslov: Drvna industrija : Znanstveno stručni časopis za pitanja drvne tehnologije
• Skrajšan naslov: Drv. ind.
• Založnik: Šumarski fakultet Sveučilišta u Zagrebu, Hrvatsko šumarsko društvo, Croatiadrvo, d. d., Exportdrvo, p. o.
• ISSN: 0012-6772
• COBISS.SI-ID: 2858754

Licence

• Licenca: CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by/4.0/deed.sl
• Opis: To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

• Jezik: Hrvaški jezik
• Naslov: Moment savijanja spojeva s čepom i rupom na križnoj potkonstrukciji sjedala stolice
• Ključne besede: stol, križna vez, upogibni moment