Numerical modeling of shell-and-tube-like elastocaloric regenerator

Ahčin, Žiga (avtor), Kabirifar, Parham (avtor), Porenta, Luka (avtor), Brojan, Miha (avtor), Tušek, Jaka (avtor)

Elastocaloric cooling is considered an environmentally friendly future alternative to vapor-compression technology. Recently, a shell-and-tube-like elastocaloric regenerator loaded in compression has demonstrated record-breaking heat-pumping performance and fatigue-resistant operation. The aim of this work is thus to present a new 1D numerical model to simulate and optimize the operation of an elastocaloric regenerator with a shell-and-tube-like design. In the first part of this work, the superelastic and elastocaloric properties of a single NiTi tube, which serve as input data for the numerical model, were determined through experimental characterization and phenomenological modeling. In the second part, the results of the numerical model were compared with the experimentally obtained results. Relatively good agreement was found regarding the temperature span, cooling and heating power, and COP values, which indicates that the developed numerical model could be used for accurate optimization of shell-and-tube-like elastocaloric regenerators. Finally, the effects of operating conditions and hysteresis losses on the performance of the shell-and-tube-like elastocaloric regenerator are modeled and discussed. This work shows that the shell-and-tube-like elastocaloric regenerator with this configuration can achieve a maximum temperature span of more than 50 K at zero-thermal-load conditions and a maximum cooling/heating power of up to 4000 W·kg−1 and COP of about 4 (at zero temperature span).

• Jezik: Angleški jezik
• Ključne besede: elastocaloric effect, caloric cooling, compressive loading, NiTi, numerical modeling, hysteresis
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: FS - Fakulteta za strojništvo
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Datum objave: 01.12.2022
• Leto izida: 2022
• Št. strani: 28 str.
• Številčenje: Vol. 15, iss. 23, art. 9253
• PID: 20.500.12556/RUL-143456
• UDK: 621.576:519.62
• ISSN pri članku: 1996-1073
• DOI: 10.3390/en15239253
• COBISS.SI-ID: 134922499
• Datum objave v RUL: 21.12.2022

AHČIN, Žiga, KABIRIFAR, Parham, PORENTA, Luka, BROJAN, Miha in TUŠEK, Jaka, 2022, Numerical modeling of shell-and-tube-like elastocaloric regenerator. Energies [na spletu]. 2022. Vol. 15, no. 23,  9253. [Dostopano 14 april 2025]. DOI 10.3390/en15239253. Pridobljeno s: https://repozitorij.uni-lj.si/IzpisGradiva.php?lang=slv&id=143456

Gradivo je del revije

• Naslov: Energies
• Skrajšan naslov: Energies
• Založnik: Molecular Diversity Preservation International
• ISSN: 1996-1073
• COBISS.SI-ID: 518046745

Licence

• Licenca: CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by/4.0/deed.sl
• Opis: To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Sekundarni jezik

• Jezik: Slovenski jezik
• Ključne besede: elastokalorični učinek, kalorično hlajenje, tlačno obremenjevanje, NiTi, numerično modeliranje, histereza

Projekti

• Financer: EC - European Commission
• Program financ.: H2020
• Številka projekta: 803669
• Naslov: Superelastic Porous Structures for Efficient Elastocaloric Cooling
• Akronim: SUPERCOOL

• Financer: ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
• Številka projekta: P2-0422
• Naslov: Funkcionalne tekočine za napredne energetske sisteme