CFD analysis of thermal fields for ice abrasive water jet

Jerman, Marko (avtor), Orbanić, Henri (avtor), Valentinčič, Joško (avtor)

Ice abrasive water jet (IAWJ) technology uses ice particles instead of the mineral abrasives used in abrasive water jet (AWJ) technology. Since the thermal conditions are extremely important for the survival of the ice particles and their mechanical properties, the temperatures of the water jet and the adjacent air are analysed for different pressures and temperatures of the water upstream of the water nozzle and different nozzle orifice diameters. The temperature fields are calculated with a fully validated Computational Fluid Dynamic (CFD) model. The results show that the temperature of the jet core does not change significantly, but the adjacent air heats up considerably due to viscous heating; both are influenced by the water temperature and pressure upstream of the water nozzle. A low water temperature upstream of the water nozzle could significantly reduce the expected temperature of the ice particles exiting the cutting head. However, the use of a cold carrier gas such as nitrogen with a temperature of -196°C should not have a significant effect on the temperature of the ice particles inside the cutting head. It is recommended to optimise the geometry of the cutting head to reduce the travel time of the ice inside. If water cooling is not used, the ice particles should have a diameter of more than 0.5 mm. However, if cooling is used, particles as small as 0.3 mm in diameter can be used. The observed temperature conditions play a key role in the further development of IAWJ technology.

• Jezik: Angleški jezik
• Ključne besede: water jet machining, CFD simulation, cold jet, IceJet technology, ice abrasive water jet, computational fluid dynamics, infrared thermography, flash abrasive water jet, thermocouple, volume of fluid, IAWJ
• Vrsta gradiva: Članek v reviji
• Tipologija: 1.01 - Izvirni znanstveni članek
• Organizacija: FS - Fakulteta za strojništvo
• Status publikacije: Objavljeno
• Različica publikacije: Objavljena publikacija
• Leto izida: 2022
• Št. strani: 14 str.
• Številčenje: Vol. 220, art. 107154
• PID: 20.500.12556/RUL-139080
• UDK: 621.924.9:532:519.62
• ISSN pri članku: 0020-7403
• DOI: 10.1016/j.ijmecsci.2022.107154
• COBISS.SI-ID: 98152707
• Datum objave v RUL: 30.08.2022

Gradivo je del revije

• Naslov: International journal of mechanical sciences
• Skrajšan naslov: Int. j. mech. sci.
• Založnik: Elsevier
• ISSN: 0020-7403
• COBISS.SI-ID: 25648384

Licence

• Licenca: CC BY-NC-ND 4.0, Creative Commons Priznanje avtorstva-Nekomercialno-Brez predelav 4.0 Mednarodna
• Povezava: http://creativecommons.org/licenses/by-nc-nd/4.0/deed.sl
• Opis: Najbolj omejujoča licenca Creative Commons. Uporabniki lahko prenesejo in delijo delo v nekomercialne namene in ga ne smejo uporabiti za nobene druge namene.

Sekundarni jezik

• Jezik: Slovenski jezik
• Ključne besede: rezanje z abrazivnim vodnim curkom, numerične simulacije, hladen curek, ledeni abrazivni vodni curek

Projekti

• Financer: ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
• Številka projekta: P2-0248
• Naslov: Inovativni izdelovalni sistemi in procesi

• Financer: ARRS - Agencija za raziskovalno dejavnost Republike Slovenije
• Številka projekta: J2-2511
• Naslov: Prilagodljivo utrjevanje površin avstenitnih jekel s procesi kriogenega preoblikovanja